Insulating Coatings

 

1201

Red Alkyd (Brush/Spray/Dip).  Bake or air dry.  Meets MIL-E22118; used for coils, armatures and other electrical apparatus.  Also used as a primer, sealer for screws, pipes, vacuum systems and hydraulic fluid chambers.

 

1201A

Red Alkyd Aerosol Spray Can version of 1201.  For convenience and ease of application.

1201B

Red Alkyd (Brush/Spray/Dip).  Bake or Air dry .  Higher solid, higher viscosity version of 1201.

1209

Gloss Black Alkyd (Brush/Spray).  Bake or air dry.  Use on small motor stators, field coatings, end windings and bus bars.  Also used as finishing coat on electrical equipment.

74004

Buff Catalyst Curing Epoxy.  74010 hardener required.  Designed to give maximum durability and resistance; used on equipment exposed to oils, coolants and other corrosive agents; frequently used on large end windings.

7815

Gloss Black Alkyd (Brush/Spray).  Bake or air dry.  Used as a finishing coat on end windings and as finish coat on electrical apparatus where resistance to oil, humidity and weather is required.

8001EW

Gloss Red Alkyd (Brush/Spray).  Bake or air dry.  Similar to 1201 except that it has a higher bonding strength at room temperature.  Recommended primarily for bakes.

C1149

ASA49 Gray Version of 74004.  74010 hardener required.

CE237

Black Alkyd (Spray/Dip).  Bake or air dry.  An offset to the 7815 with improved arc resistance.  Designed for finishing motor end windings for oil and chemical resistance.

CE387

Blue Epoxy (Brush/Spray).  Air dry.  74010 hardener required.  Designed for heavy duty resistance to oil, coolants, corrosive agents to give maximum durability and chemical resistance.

 

 

Insulating Varnishes

 

1202

Clear General Purpose Insulating and Finishing Alkyd Varnish.  Air dry.  Excellent heat resistance.  Up to 145C on non flexing equipment.

9620

Clear Insulating and Finishing Varnish.  Air dry.  Excellent oil, moisture and acid resistance.  Up to 130C on non flexing equipment.

 

Semi-Conductive Coatings

 

9921

Dark Green Flat Semi-Conducting Paint.  Air dry.  Designed for equalizing voltage stress and to prevent or decrease corona discharge.

 Resistivity: 2000-20000 OHMS/SQ.

 

Hardener

 

74010

Epoxy Hardener.  For 74004, C1149, CE387

 

 

Adhesives

 

880

A Thermoplastic Shellac Base Adhesive.  Designed for bonding gaskets; used wherever excellent oil resistance is required, i.e., transformers, etc.

1276

Fast Air Drying General Purpose Adhesive.  For bonding porcelain, glass, leather, cork, paper, metals, fabrics, some rubbers and cements.

2142GN

Fast Air Drying Thermoplastic Vinyl Cement.  Durable bonds, has excellent resistance to oil, gasoline and moisture.

C1800

Very High Viscosity Version of 1201.  For use as a dipping gasket adhesive; does not have the electrical properties of 1201.

7526F

General Purpose Adhesive with Fungicide Resistant Properties.  Its basic use is for tamper proof application over screws.

 

 

Industrial Primers-Solventborne

 

7920

Pearl Gray Zinc Chromate Alkyd Primer (Spray).  Air Dry.  Designed for use on metal substrate.  Fast dry, sandability, lacquer topcoat acceptance along with humidity and corrosion resistance makes this coating the ideal “shopcoat” primer.

8001

Red Oxide Primer (Spray/Dip/Flow).  Bake or air dry.  Excellent humidity, corrosion, and oil resistance.  Adheres to phenolic.

C1149

ASA49 Catalyst Cured Epoxy.  (Brush/Spray).  74010 hardener required.  Used as a primer/topcoat for maximum corrosion, oil, coolant, and chemical resistance.

C1968

High Solid Gray Primer/Topcoat. (Spray).  Air dry.  Designed for use on metal substrates. Excellent sandability and corrosion resistance.  This product can be topcoated with various lacquers and/or two package urethanes.

 

Industrial Topcoats-Solventborne

 

1559

White Gloss Alkyd Nitrocellulose Lacquer (Spray/Dip).  Air dry.  Custom finish for industrial products.  Suitable for hospital and kitchen equipment.  Good exterior durability with excellent gloss and color retention.

2600

Black Gloss Alkyd Nitrocellulose Lacquer (Spray/Dip).  Air dry.  Excellent weather durability and arc resistance.  Used for electrical equipment, instruments and switchgear.

7496

Gray Low Gloss Alkyd Enamel (spray/dip).  Bake or air dry.  Designed for finishing of motors and other electrical equipment where good arc resistance is required.  Interior exposure only.

7815

Black Gloss Alkyd (Brush/Spray/Dip).  Bake or Air dry.  Designed as a finish coat on end windings and electrical equipment.  Excellent oil, humidity and weather resistance.

8112

ASA #49 Gray Low Gloss Vinyl Alkyd (Spray).  Air dry.  Designed as a finish for motors, switchgear and as a general purpose equipment finish with good oil and weather resistance.

8238

ASA #49 Gray Medium Gloss Vinyl Alkyd (Spray)  Ready-to-Spray.  Air dry.  Designed for motors and equipment in the motor repair industry.  Used for transformers, machines, switchgear and other electrical apparatus.

8239

ASA#61 Gray.  Properties are the same as 8238 but in a #61 Gray.

8240

Forest Green.  Properties are the same as 8238 but in a Forest Green.

G788

Light Gray Gloss Enamel ASA #70 (Brush/Spray)  Air Dry.  A durable enamel for finishing apparatus to be stored or operated outdoors.  Equally suitable for interior use.  May be used on metal or wood.

G1228

(Aerosol

Avail.

1228A)

Dark Gray Gloss Enamel ASA #49 (Brush/Spray)  Air Dry.  A durable enamel for general finishing of machinery and electrical apparatus.  Has excellent outdoor durability and high resistance to transformer oils.  May be used on metal or wood.

G6332

Dark Green Gloss Enamel (Brush/Spray)  Air Dry.  A durable enamel for finishing apparatus to be stored or operated outdoors.  Equally suitable for interior use.  May be used on metal or wood.

G3415

Medium Gray Gloss Enamel ASA #61 (Brush/Spray)  Air Dry.  A durable enamel for general finishing of machinery and electrical apparatus.  Has excellent outdoor durability and high resistance to transformer oils.  May be used on metal or wood.

 

 

Industrial Primers-Waterborne

 

C1815B

Beige Waterborne Alkyd Primer (Spray).  Air dry.  Designed for single coat application on components subject to exterior exposure.  C1815B is formulated to contain a minimum level of trace elements and is recommended for use in atomic power installations.

 

 

 

Metal Primers

 

1248

Red Chromate Low Gloss Primer (Brush/Spray/Roll).  Air dry or bake.  Designed for the protection of interior or exterior metal surfaces against corrosion.  It is a general purpose primer giving excellent rust protection and weather durability.

1272

Red Iron Oxide Low Gloss Primer (Brush/Spray).  Air Dry.  Designed for use on structural steel and all ferrous metals.  The paint has rust inhibitive characteristics and is recommended as a shop coat primer for steel when it is not exposed to the elements for an extended period of time.

7635

Red Iron Oxide Zinc Chromate Primer (Brush/Spray).  Air dry.  An excellent inhibiting primer for metal surfaces such as transformer tanks, switchgear cabinets, machinery, etc.  Should be followed by finish coat selected to suit the exposure.  Interior or exterior service.

 

 

High Temperature Coatings

 

1212

Aluminum Gloss Alkyd Enamel (Brush/Spray).  Air dry or bake.  It is 1202 Glyptal varnish furnished with an aluminum paste in a two compartment container for on-the-job mixing.  1212 is suggested for finishing equipment which must stand prolonged temperatures of up to 400F

86009

Aluminum Low Gloss Silicone (Spray).  Bake.  A ready mixed aluminum silicone resin product designed for high temperature applications.  It provides durable protective coating on metal surfaces subjected to temperatures

400F-1200F.  86009 is suggested as a finish for ovens, jet engines and other metal surfaces needing protection during high temperature exposure.  Optimum results are obtained by applying multiple thin coats (0.2-0.5 mil).

S1193

Class A & B Gray Silicone Epoxy Finish (Spray/Bake).  Applications include ovens, protective finishes on jet engine components(meets GE Aircraft Engine specification number F50TF3-53) aircraft and marine surfaces, solar energy systems and high temperature automotive components.  The coatings may be applied to aluminum, magnesium or steel.

S1195

Class D Resinous Reducer.  Used for S1193 Silicone epoxy.